Post a Comment On: Fawcett Avenue Conscripts

I had a hard time focusing during the last week of January, ricocheting around from project to project without seeming to get closer to completion. Eventually things started falling into place, and I ended up with 9 completed vehicles. Some of these have been sitting in my 'IN' box for over a decade, so it felt good to finally get them ready for the gaming table.First up is a DUKW with a British RASC driver. This was a toy dating from the 1960s that originally belonged to my younger brother. It suffered some 'battle damage' at some point, and my brother was no longer interested in it. I thought I might be able to fix it, and it seemed like the right scale for 28mm gaming. In fact, measuring its length and comparing it to the length of an actual DUKW, it works out to be 1/56. The only 'flaw' is that it only has a single axle in the rear instead of two. I have no idea who manufactured it, but it reads 'NOVELTY' and 'Made in Hong Kong' on the bottom.  [Image]
The broken pieces near the back and the front right wheel well were filled in using epoxy putty, while the front windshield was fashioned from pieces of clear plastic cut from a CD case. The crates and fuel drums came from a Bandai Maultier kit, and the driver is an old Bolt Action jeep driver that I had in my 'bits box' along with the rolled up tarp. It is now ready to ferry supplies or a squad of commandos across a river or from ship to shore. 
[Image]
[Image]
[Image]
Next up is a Kübelwagen Type 82/3. This was a mock-up scout car/armoured vehicle with a machine gun-turret atop the cabin. It was apparently built for decoy and training purposes. I bought this from Wargames Foundry decades ago. It came with the Feldgendarm, but I only painted up the 'Kettenhund' as I couldn't decide the colour scheme that would be most appropriate. Eventually I thought Panzer Dunkelgrau would do just as well as any other colour, and now it's finally done. [Image]
[Image]
 Third on our list is a Bandai 1/48 SdKfz 3 Maultier that I picked up off Ebay. This was another project where I couldn't decide what colour to paint it, but I finally decided to go with Panzer Dunkelgrau with an Olive Green striped camouflage suitable for the Russian Front. The tarp was painted Tan Earth and given a wash of GW Agrax Earthshade. I then liberally applied Vallejo European Dust wash everywhere. The kit came with a cargo of four petrol drums and two large crates, but since nobody would see them with the tarp in place, I used them for the DUKW. [Image]
[Image]
[Image]
 Next is a 3D printed French Panhard 178 armoured car that was from the same run as the two painted by Fellow Conscript DallasE. I used a different paint scheme that is based on a surviving example in the Musée des Blindés in Saumur, France. I used Vallejo Gunship Green and Chocolate Brown with a sharp black line in between. I left off the fifth wheel, but added a muffler on the right side made from a piece of plastic sucker stick. Sometimes it helps a recce unit to not be heard, as well as not be seen. The decals were all ones that were kicking around in my files, so I didn't have to free hand any roundels.  [Image]
[Image]
[Image]
The fifth item is a group of four M5 Half-tracks to provide some additional armoured lift capability to my 2nd Canadian Division. I am not sure if these were used in any of the infantry divisions, so I may have to mark them up for the 4th Canadian Armoured Division. The models are either Corgi or Solido 1/50 vehicles that all came in different colours and configurations. One was an ambulance version that had a tarp on it, and the back door was cut out. The tarp was tossed in the 'bits box' while the missing door was replaced using thin plastic card. Everything was painted a uniform colour and then 'muddied up'. The verdict is still out on what stars should be added and where, but the vehicles are now ready to take to the field and move a platoon of infantry in relative safety on the battle field. [Image]
[Image]
 The last vehicle of this post is a Warlord Games 1/56 resin and metal M10 Achilles mounting a 17 pounder. While this is a newer acquisition compared to some of the other vehicles, it sat on the shelf for a while before being assembled. When it arrived, the tracks were warped and didn't form a clean fit with the chassis. A bath in some boiling water and some careful pressure in the right places straightened things out to an acceptable degree and things proceeded readily from there. Two of the crew in the turret are part of the resin casting while the third crewman is in metal. All came with separate heads which can provide some variety if you want to field more than one. The tarps were added from my 'bits box'. The only two Canadian units that used 17pdr M-10s were the 4th Anti-Tank Regiment RCA of the 5th Canadian Armoured Division; and the 7th Anti-Tank Regiment RCA of the 1st Canadian Corps Artillery. Both Regiments would have had two batteries of towed 17pdrs and two SP batteries with 17pdr M-10s [Image]
[Image]
[Image]
[Image]
 As I said in the title, it is definitely a mixed bag of vehicles, but they are now all done.Thanks for reading.